This article will introduce you to such a procedure as laying paving stones with your own hands: step-by-step instructions for paving sites and paths, supported by photos and videos, will include a complete overview of recommendations for choosing materials, planning future construction and its implementation. The specificity and benefits of using materials such as paving stones and paving slabs will be discussed in detail.

The area in front of the entrance to the house is paved with paving slabs

The area in front of the entrance to the house is paved with paving slabs

In the photo, paving stones in the courtyard of private houses can be seen as decoration:

  • tracks;
  • summer recreation areas;
  • barbecue areas;
  • courtyard and entrance to the house;
  • areas for placing a car in front of the house;
  • areas around the gazebo, shed or bench;
  • areas under a carport, etc.

Paving stones belong to the category of reliable materials with a high level of strength and wear resistance. It has one undeniable advantage. Taking a look at the asphalt roads and the state they are in, it immediately becomes clear that the old cobblestone streets benefit in many ways. Even after 100 years of use, this antique coating retains its durability without being repaired.

Note! Paving stones will provide the same quality and durability in your yard, but only if you choose the right materials and fully comply with the paving technology requirements.

The summer patio is decorated with paving stones, laid out in a circular way

The summer patio is decorated with paving stones, laid out in a circular way

Initial recommendations

Before starting work, you should take care of preparing the necessary materials and tools.

Initial recommendations:

  • before you go to buy consumables, you should carefully measure the area for laying the coating, deal with schemes and patterns, and also calculate the required amount of paving stones with a small margin in case damage occurs during work;
  • together with the material, you should purchase a dry paving mix. If you intend to lay paving stones on concrete, as a rule, such paths can last for several decades. Or purchase other components for work on a sandy surface;
  • if there is a need, you need to buy or rent the missing equipment and tools;
  • enlist the support of an assistant, since it is quite difficult to lay the sidewalk on your own, or call specialists. It will be problematic to cope with such a large array of work alone, especially if you do not have enough experience and knowledge.
A neat garden path, paved with your own hands

A neat garden path, paved with your own hands

Paving stones are small products made of natural stone. Most often, this type of coverage is found on pavements, but due to its natural origin, which ensures the preservation of its shape for a long time, it is often used for paving paths in the courtyards of private houses.

Features of the choice of paving stones for paths in the country, prices for concrete material

Concrete paving stones are among the most commonly used materials for paving sites and sidewalks. In production, concrete is used for the manufacture of blanks. Special plasticizers are added to this mixture, as well as pigments of various colors.

Note! Concrete slabs can be created using different technologies - vibropress or vibratory casting. In each case, the coating acquires special properties and advantages.

The cost of concrete tiles ranges from 300 to 500 rubles per square meter

The cost of concrete tiles ranges from 300 to 500 rubles per square meter

The production process, during which concrete paving stones are created, is as follows:

  • preparation of concrete mix;
  • filling forms;
  • special processing of the mixture;
  • drying stage.

After complete drying of the concrete, the finished workpieces are removed from the molds. During the drying period, the concrete mixture hardens and gains strength.

If you want to purchase concrete paving stones for work, along with a low and affordable cost, you get quite acceptable performance properties. This material option is suitable if the construction budget is limited.

Prices for gray cement paving stones:

Product shape Cement grade Dimensional parameters, cm Price, RUB / m²
Paving stones M400 20x10x4 325
Rectangle M400 20x10x4 346
Paving stones M300 20x10x5 352
Paving stones M400 24.3х12х7 357
Brick M400 20x10x6 358
Brick M400 20x12x6 362
Paving stones M200 20x10x5 374
Paving stones M300 20x10x4 380
Paving stones M400 20x10x7 387
Paving stones M300 20x10x6 440

 

Features of other types of paving stones

In addition to concrete paving stones, there are other types of coating. Clinker material is made on the basis of clay. Blanks are a kind of bricks used for paving sites. Clinker paving stones have different shapes and colors. This type of material is distinguished by its increased strength, durability and resistance to low temperatures.

Stone paving stones for areas and sidewalks are considered by developers as a classic coating option. The material for its manufacture is natural stone, mainly:

  • marble;
  • granite;
  • basalt.
Basalt tiles are often used to decorate the local area

Basalt tiles are often used to decorate the local area

There are many ways to lay stone paving stones, making it possible to create a pavement that can last more than a century.
The modern assortment offers several varieties of this material.The classification is based on the external characteristics of the blanks, which can be:

  • sawn;
  • chipped;
  • chipped and sawn.

Useful advice! Use special types of paving stones to organize the coverage on paths and terraces. For these purposes, products made of high quality colored concrete or ceramics are provided.

Granite paving stones: material features

Paving stones from granite are natural coatings. Its uniqueness lies in the fact that in the conditions of advanced technical progress, specialists have not yet been able to create a technology for obtaining an artificial analogue of this stone, which has the same service life, level of strength, and also resistance to weathering.

Chipped granite paving stones

Chipped granite paving stones

The chipped version of the material is used in the classic design. The coating is able to withstand significant operational loads, so it can be called almost eternal. While budget cement paving stones can last no more than 20 years.

Granite is extremely stable and therefore best suited for paving:

  • sidewalks;
  • sites;
  • highways;
  • park paths.

During the period of long-term operation, the stone practically does not undergo external changes, it retains its properties.

The process of paving the sidewalk with granite tiles

The process of paving the sidewalk with granite tiles

Advantages of Granite Paving Stone Coating

Advantages of using granite paving stones:

  • stone blanks have an increased strength index, due to which the entire coating is also durable;
  • due to its dense structure, granite acquires moisture resistant properties. Moisture cannot penetrate into the deep layers of the material, so the paving stones are not afraid of severe frosts and rains;
  • stable structure protects granite from the damaging effects of chemicals. The same property provides the material with excellent performance characteristics;
  • natural destruction of the material is very slow. The stone is not susceptible to cracks, burnout, does not show vulnerability to the effects of putrefactive processes and atmospheric phenomena. The natural pattern of the rock is preserved practically in its original form;
  • chipped paving stones do not absorb dirt particles, self-cleaning in the rain, does not contribute to the accumulation of moisture on the surface. Granite is not afraid of ultraviolet radiation;
  • The paving stone cover is easy to repair, and the blanks themselves can be used for re-paving. Multiple use of the material does not affect the quality of the tracks.
A path made of granite paving stones will last for more than a dozen years

A path made of granite paving stones will last for more than a dozen years

Note! Chipped granite has a fairly high strength index. The stone is able to withstand high pressure, strong impacts, high permeability conditions (the surface is not rubbed off), static loads.

Paving stones and paving slabs: laying options, photos, schemes

Modern paving stones and tiles come in many different shapes and colors. Thanks to this, it becomes possible to make an interesting design solution in the yard of your house. These coatings are excellent tools for decorating the local area. They are characterized by reliability and practicality, which allows them to operate tracks and sites for many years.

Even the usual brick-shaped tiles or paving stones can be used to create various patterns. To do this, it is enough to choose an interesting scheme and purchase material of the corresponding colors. Thanks to this, you can improve the aesthetics of the coating and even maintain the style in which the design of your suburban area is made.

Combination of circular and classic paving

Combination of circular and classic paving

On the basis of several types of tiles, you can create interesting patterns by laying the coating according to a certain pattern.You can develop a drawing yourself or use ready-made options for laying paving slabs:

  • geometric shapes, such as colored diamonds on a solid background. To give the image a complete look, you can use a third color to add some kind of border around the edge of the track;
  • zigzags resembling the letter "M". In work, you can use 2-3 colors and paving stones of various widths. The drawing will turn out to be dynamic;
  • complex geometric patterns look no less impressive. For work, it will be enough to choose two colors that contrast with each other. You can create something like a maze or decorate the path with twisted spirals in the form of a Greek pattern;
  • the staggered arrangement of paving stones or diagonally is very often used in the design of paths and platforms. The two-tone colors can be varied by using lines of different thicknesses and sizes;
  • a rigorous design can be achieved by repeating geometric shapes of the same size, for example, rhombuses, squares, rectangles.
Examples of simple layouts of paving slabs: 1 - herringbone, 2 - spiral, 3 - ladder, 4 - checkerboard

Examples of simple layouts for paving slabs: 1 - herringbone, 2 - spiral, 3 - ladder, 4 - checkerboard

Useful advice! If you are using repeating geometric shapes, be sure to eliminate any irregularities. Prepare the substrate carefully before laying so that the pattern does not look crooked. Paving in this case should also be given special attention.

Even the simplest patterns will effectively decorate any yard. Using curly or straight types of paving stones, you can emphasize and highlight certain advantages of the local area.

Unpretentious at first glance, two-tone patterns will look pretty decent if you do the work step by step and carefully. In this case, it is worth adhering to the advice of specialists in order to achieve the most accurate and even surface. Otherwise, even the highest quality and most expensive material, which will be laid in intricate patterns and designs, will have a sloppy and cheap appearance. Neglect of technology leads to the formation of unevenness and height differences over the surface of the coating.

Figured paving using paving stones of different colors

Figured paving using paving stones of different colors

Laying paving stones with your own hands: step-by-step instructions for work

Paving stones have many advantages. Among them, the following qualities stand out:

  • compressive strength;
  • long service life;
  • attractive appearance;
  • abrasion resistance;
  • wide range of applications, including paths, rest areas, pedestrian walkways, parking areas and traffic areas;
  • high level of resistance to temperatures, both low and high.

Useful advice! If the pavement will be subjected to serious stress in the future, it is recommended to pave the sidewalks over the concrete base. A sand pillow will not work for this purpose.

The recreation area is made of cement paving slabs

The recreation area is made of cement paving slabs

Paving stone sidewalks: how to lay the cover and where to start

Preparatory work should be done before laying paving stones. The list of these works includes the following procedures:

  1. Determine the condition of the pavement under the pavement.
  2. Choose a circuit in accordance with the planned loads.
  3. Prepare the surface for work.

To carry out the work, you will need to prepare the appropriate tools and additional materials:

  • paving stones or paving slabs;
  • a mallet with rubber pads or a hammer with a similar coating;
  • building level;
  • grinder from sets of discs for cutting tiles;
  • tape measure, shovel, brush, rake;
  • container (metal);
  • block of wood;
  • watering can, wheelbarrow;
  • sand and a special sieve for sifting it;
  • protective gloves for hands and goggles.
Before you start laying tiles, you need to prepare all the necessary tools and materials.

Before the start laying tiles you need to prepare all the necessary tools and materials

If you correctly calculate and design the site or track, in the future you will insure yourself against alterations, and, consequently, against additional costs for the purchase of material. At this stage the shape of the paving stone is selected. How to properly lay this type of coverage will also depend on other factors: paving patterns, mosaics, color scheme, surrounding landscape, as well as the base.

Using a tape measure, a set of wooden pegs, a construction cord, and a level, mark the area for setting up the pad or paths. Instead of a building level, you can use a level.

Useful advice! Be sure to walk along the pavement area and check how convenient the location you have chosen, whether the paths are obstructing the passage of motor vehicles. This stage of work still allows you to make changes without harming your project.

In the process of paving, you cannot do without a rubber mallet and a building level

In the process of paving, you cannot do without a rubber mallet and a building level

After that, it is necessary to calculate the consumables:

  • cement;
  • paving stones;
  • curbs;
  • crushed stone;
  • gravel;
  • sand.

Related article:

trotuarnaya-plitka-dlya-dorozhek-na-dache-tsenyi-4Paving slabs for paths in the country. Prices, types and styles. Paths in the country, paved with paving slabs. Correct selection and laying of paving slabs. Photos of finished tracks and sites.

Substrate preparation: how to lay paving stones on sand and gravel

The quality of the future coverage is largely determined by how carefully you think over and prepare the base.

The first stage involves preparing the soil. To do this, remove the top layer (sod) from the surface of the earth. After that, you will need to remove a layer of soil 20 cm thick. Pipes can be placed under the base of the future coating, which will subsequently be used to lay elements of communication systems. Thus, you do not have to break paths to lay communications.

Preparation of the site intended for paving slabs

Preparation of the site intended for paving slabs

Then the resulting depression is filled with gravel with large fractions or crushed stone. This is done in order to form a cushion for laying paving stones. Depending on the purpose of the tracks, a certain thickness of this layer is selected. It is recommended to take a thickness of 10-15 cm for laying a pedestrian path.If it is planned to build a parking area and a passage for cars, then this figure should be increased to 15-20 cm.

To shrink the crushed stone pad, you can use a vibrator or a conventional rammer. On top of it, an intermediate layer of sand is poured, after which it is leveled with a rake and compacted a little. It is allowed to use a dry sand-cement mixture with the ratio of these components 1: 5, respectively.

Useful advice! The height of the interlayer should be about 3-5 cm, so that as a result, the surface of the tiled coating rises 1 cm above the planned level of laying. Over time, the paving stones gradually shrink, so this gap is designed to compensate for the height difference that forms during operation.

Leveling the base with a cement-sand mixture

Leveling the base with a cement-sand mixture

Additional recommendations for arranging the base

In order for the base to turn out correct and well-planned, it is recommended to install guides that eliminate irregularities. For these purposes, it is best to take slats or pipes, through which excess material will be screed from the upper layer.

On top of the rubble is laid geotextile... This type of material should be laid in 2 layers for greater efficiency. The advantages of using geotextiles:

  • the material does not allow interlayers of crushed stone and sand to mix;
  • normal outflow of water is ensured;
  • the base turns out to be durable and more durable;
  • the probability of weeds germination between the paving stones is excluded (plants contribute to the destruction of the paved surface, reducing its service life).

If you adhere to all the recommendations for forming the base, this site will become an excellent basis for laying tiles or paving stones. Thanks to the exact adherence to the technology, the platform or paved path will be durable and will not sag over time.

The final result will directly depend on the quality of foundation preparation.

The final result will directly depend on the quality of foundation preparation.

Do-it-yourself paving stone coating: video. How to lay curbs

There is no more suitable material for paving paths in the courtyard of a country house than paving stones. Many owners of such cottages know how to lay this type of coating with their own hands. After all, this is a great way to save money on the arrangement of the local area and make it comfortable and beautiful. For the paths to have a complete appearance, curbs should be installed before paving the paving stones.

The border will perform several functions at once:

  • decorative (the coating gets a beautiful frame and a harmonious appearance);
  • limiting (paving stones will not creep on the sides due to the outflow of water);
  • strengthening (the base becomes stronger and more stable).

Before installing the curbs, model the area or path you are going to make with wooden pegs. Indicate all bends, turns, and intersections.

Useful advice! In places where the path bends, trim off the corners of adjacent curbs. Use a grinder for these purposes.

Curb path looks cleaner

Curb path looks cleaner

Next, all the pegs need to be connected together with a rope or cord. Be sure to use a building level or level when doing this. Dig the groove in such a way that the curb on the cushion is about 1 to 2 cm above the rope. Put concrete mixture at the bottom of this groove.

The curb is installed on the prepared pillow, after which it should be hammered in by lightly tapping a rubber hammer or mallet until the surface is level with the tension level of the rope.

When installing the curb, you should control its position. Each element must be checked for verticality, which it must strictly comply with. Then the gaps between the elements of the border are controlled. These parts should be installed as tightly as possible to each other. The groove itself from the outside should be covered with sand and tamped thoroughly.

In some cases, designers do without the use of borders during the installation of paving stones. A video on how to properly lay material in such conditions can be easily found on the Internet. Basically, the paving is carried out flush with the lawn or 1-2 cm above it.

We carry out the laying of paving slabs with our own hands: step-by-step instructions, video

Paving slabs are laid manually on a diagonal basis. The workpieces are placed on the surface of the base in the direction "away from you". This is done in order not to violate the integrity of the prepared and even top layer. Make sure that there is a gap of about 1-2 mm between the workpieces.

Useful advice! The easiest to install is the "Old Town" tile. Its blanks have special protrusions that prevent the elements from tightly fitting to each other.

In the future, these gaps will be filled with sand or a special dry mixture. This procedure is performed in order to fix the tiles in the desired position. Sand during the operation of the coating will not allow the blanks to move from their places.

After the tile is laid on the surface of the base, it should be tamped. This must be done very carefully so as not to spoil the workpiece. Use a rubber mallet or wooden mallet to do this. Perform visual control of the placement of each element in accordance with your chosen installation scheme.

For even laying of tiles along and across the rows, a rope is pulled

For even laying of tiles along and across the rows, a rope is pulled

If it was not possible to install the tile as expected, the workpiece should be lifted, the amount of sand under it should be adjusted (removed or, conversely, filled up), the surface should be leveled with a tamper and again try to install the element correctly.

If the project is supposed to create a site or track of irregular shape, with turns or roundings, you will need to cut the material. Any version of the tile covering lends itself well to cutting. For these purposes, it is better to use a grinder. Stock up on a set of discs designed for working with stone surfaces.

Before proceeding with the cutting of the material, the tiles should be attached to the intended installation site and marked with a line. It will cut off the unnecessary part that goes beyond the border. To avoid waste of material, it is recommended to cut the tiles last, when the solid pieces have already been laid.

Paving a path with installed curbs

Paving a path with installed curbs

When the rough laying is completed, a control check of the placement of the tiles is carried out using a rule or a building level for the presence of defects in the coating:

  • irregularities;
  • depressions;
  • bulges.

After all defects have been eliminated, the coating is covered with river sand with a fine fraction or a mixture of sand and cement. Use a mop, broom or brush to remove excess. Use a hose to spray the coating. This completes the installation of the pavement.

Use the video material to visually see how the tile is laid. Subject to technology and selection of quality materials, paving paths will decorate your country yard for a very long time.